Timer Programs Functions for automatic or manual single-motor doors with slowdown and anti-crushing

Timer Programs Functions for automatic or manual single-motor doors with slowdown and anti-crushing

Timer

Functions for automatic or manual motor gates with slowing down and anti-crushing in closing and opening, with electric photo cell, with 2 open and closed stops, limit switches through external inputs, internal limit switches. NOTE: the internal limit switches are by ammeter. If the automation or the gate were in bad condition, the internal limit switches would act if this happens open to correct the gate (for safety because it would act as anti-crushing) 1st. Function: MI1 giving an impulse, the automation will begin to open with an acceleration ramp, it will count a time already programmed.

Timer

Functions for automatic or manual motor gates with slowing down and anti-crushing in closing and opening, with electric photo cell, with 2 open and closed stops, limit switches through external inputs, internal limit switches. NOTE: the internal limit switches are by ammeter. If the automation or the gate were in bad condition, the internal limit switches would act if this happens open to correct the gate (for safety because it would act as anti-crushing) 1st. Function: MI1 giving an impulse, the automation will start to open with an acceleration ramp, it will count a time already programmed, ending with a slowdown, reaching the opening limit switch. This function takes precedence over all closing functions. 2nd. Function: MI1 holding two seconds (note this option will only work when the opening limit switch is pressed by the open door) the automation will begin to close with acceleration with a time already programmed, ending with a slowdown, reaching the limit switch. close MI5 NOTE. To close the automation without waiting for opening, press MI2 (this option is to make the automation have a button to open and another button to close). Suppose the automation is closing if MI1 is pressed, the automation stops and starts to open. Function: AVI photo-cell note: This option only works, when the automation is in the closing and slowdown state, explanation: The automation is closing, if we cross the photo-cell, the automation will stop and do the reverse, that is, it will open until it reaches the opening limit switch. NOTE: When the photocell is cut off (only when closing) it will reverse at a reduced speed, until it reaches the end of the opening stroke. While the photocell is operating, no function will work except for the stop. It is important to set the cell opening parameter for the longest time since the slower the time must be longer to open. 4.Function: STOP Here we will find two types of stop, total stop or stop whenever the automation is in operation both in closing and opening when pressing MI3 or MI4 the automation will stop immediately or stop. MI4 is an open contact when this contact is closed for a stop (it is used for the digital keypad), MI3 this contact is closed when it is opened for a stop (it is used for pneumatic bands, infrared band or radio active) note if it refuses the bands will have to make a 24v bridge to MI3. This function prevails over all functions. 5th. Function: MI5 limit switch open, explanation: the automation is opening when MI5 is pressed, the automation will stop. This function prevails over all opening functions. 6th. Function: MI6 limit switch close, explanation: the automation is closing when MI6 is pressed, the automation will stop. This function overrides all closing functions. * 7: 1st. Function: MI4 Explanation of manual: we will give MI1 or the remote control button, if there is one, it will start to open, reaching the end of the stroke, open and stop the automation, waiting for the closing pulse to be given. This option is called step by step or manual. Automation will be automatic, explanation: giving an MI1 pulse or command, the automation will begin to open making its entire opening travel, it will count a pause time or stop door and it will begin to close and so on. Note: you can also advance the closing if you do not want to wait for the pause, how would we do it? The door will begin to close, skipping its pause time. * HOW TO PROGRAM THE AUTOMATIC IN AUTOMATIC OR MANUAL: By keeping MI4 pressed for a period of 15 seconds, the automation will become automatic, to change it to manual we will have to keep MI4 pressed for a period of 8 seconds.